Clutch not working
-
- Studying MC Handbook
- Posts: 98
- Joined: Wed Jan 07, 2015 2:30 pm
- My Bike: 2000 VS 800 Intruder
Clutch not working
I have a 2000 vs800 with 76,000. My clutch will not work. I bled the line and it still does not work. When I put it in gear it jumps and goes dead. I think I have all the air out of the line. What else could the problem be? We rebuilt the clutch parts on the handlebar a few years ago. Thanks.
-
- Joined a 1100cc Club
- Posts: 5511
- Joined: Thu Dec 29, 2016 12:33 pm
- My Bike: VS800
Re: Clutch not working
It's probably still air in the line. It is very difficult to remove.
Try reverse bleeding, and also cracking the banjo fitting to bleed there.
Try reverse bleeding, and also cracking the banjo fitting to bleed there.
-
- Studying MC Handbook
- Posts: 98
- Joined: Wed Jan 07, 2015 2:30 pm
- My Bike: 2000 VS 800 Intruder
Re: Clutch not working
Navigator, thanks. I will try reverse bleeding as per Clymer manual.
- WintrSol
- Joined a 450cc Club
- Posts: 857
- Joined: Fri Feb 26, 2016 2:02 pm
- My Bike: CB450 GL1500CT
- Location: Near St. Louis, MO
Re: Clutch not working
When you do that, move the reservoir so the banjo is lower than the rest of the MC, so air will be pushed up and out.
Florissant, MO
CB450K3, GL1500CTValkyrie
CB450K3, GL1500CTValkyrie
-
- Studying MC Handbook
- Posts: 98
- Joined: Wed Jan 07, 2015 2:30 pm
- My Bike: 2000 VS 800 Intruder
Re: Clutch not working
We took the banjo bolt off and held my thumb over the hole and pumped the lever. There was pressure there so I quickly put the banjo bolt back on. We bled the line and got a bunch of air out but still no pressure on the clutch. We bled it until there was no air in the drain tube. When I crank it and put it in gear it lunges forward. So next is to reverse bleed. What does he mean by putting the banjo bolt lower than the rest of the master cylinder? I assume MC is master cylinder. I drilled a hole in the top of a twelve ounce can of brake fluid and put a four foot clear tube in the can of brake fluid. Will I need to drill a hole in the top of the brake fluid can so it can get air? Do I back bleed it with the banjo bolt loose from the master cylinder? Then pump the lever with my thumb over the hole and put the banjo bolt back in? Or do I leave the banjo bolt screwed in and which will force the fluid into the reservoir? Thanks.
-
- Joined a 1100cc Club
- Posts: 5511
- Joined: Thu Dec 29, 2016 12:33 pm
- My Bike: VS800
Re: Clutch not working
The problem is usually a high spot in the line as it snakes along the frame.
COVER your paint.
You can use a pump style oil can and force brake fluid through the bleeder on the slave...or you can hang a funnel above the master cylinder (MC) level and gravity feed fluid down a tube from the funnel through the slave cylinder.
If you use a pump, fluid can easily be forced through the small hole in the floor of the MC and shoot fluid 6 feet out of the hole so be careful. If you use gravity the process is much slower, keep the funnel full until the MC is full, then pinch off the funnel hose with some vice grips and close the bleeder.
What he means is to either loosen the clamp on the MC and slide it along the handlebar...or turn the handlebar until the banjo bolt fitting is at the lowest point of the MC, you may want the MC at a slight angle upward from the banjo to let the air rise up and out of the small holes in the MC floor.
Either way the fluid will fill from the bottom and force the air upwards and out.
Pump style can:
https://www.napaonline.com/en/p/BK_5751 ... pcQAvD_BwE
COVER your paint.
You can use a pump style oil can and force brake fluid through the bleeder on the slave...or you can hang a funnel above the master cylinder (MC) level and gravity feed fluid down a tube from the funnel through the slave cylinder.
If you use a pump, fluid can easily be forced through the small hole in the floor of the MC and shoot fluid 6 feet out of the hole so be careful. If you use gravity the process is much slower, keep the funnel full until the MC is full, then pinch off the funnel hose with some vice grips and close the bleeder.
What he means is to either loosen the clamp on the MC and slide it along the handlebar...or turn the handlebar until the banjo bolt fitting is at the lowest point of the MC, you may want the MC at a slight angle upward from the banjo to let the air rise up and out of the small holes in the MC floor.
Either way the fluid will fill from the bottom and force the air upwards and out.
Pump style can:
https://www.napaonline.com/en/p/BK_5751 ... pcQAvD_BwE
-
- Studying MC Handbook
- Posts: 98
- Joined: Wed Jan 07, 2015 2:30 pm
- My Bike: 2000 VS 800 Intruder
Re: Clutch not working
CLUTCH IS WORKING GREAT. I did what you said witH an oil can pump, First thing I did was slide the MC on the handlebar until the banjo was lower than the hole in the MC. Then hooked a clear line full of fluid (on the oil can pump) to the slave. A few pumps and a few air bubbles later and everything is great. The metal plate under the cover came off and there was a lot of crud to clean up. THANKS. THANKS VERY MUCH.
-
- Joined a 1100cc Club
- Posts: 5511
- Joined: Thu Dec 29, 2016 12:33 pm
- My Bike: VS800
Re: Clutch not working
I love it when a plan comes together!LSU Tiger wrote: ↑Sun Oct 25, 2020 12:31 pmCLUTCH IS WORKING GREAT. I did what you said witH an oil can pump, First thing I did was slide the MC on the handlebar until the banjo was lower than the hole in the MC. Then hooked a clear line full of fluid (on the oil can pump) to the slave. A few pumps and a few air bubbles later and everything is great. The metal plate under the cover came off and there was a lot of crud to clean up. THANKS. THANKS VERY MUCH.