throw-over saddlebag install
-
- Practicing Bicycling
- Posts: 37
- Joined: Sun Sep 03, 2017 5:40 am
- My Bike: 1996 Suzuki Intruder 1400
throw-over saddlebag install
I went to install my new set of River Road throw-over saddlebags, but couldn't get my passenger seat back on (wouldn't sit low enough to use original rear seat bolt). I placed the throw-over straps on top of the electrical bundle under the passenger seat. Any issues with strap on top of electrical bundle? Any experience moving the electrical bundle? Pics would be useful. Thanks.
-
- Joined a 1000cc Club
- Posts: 3968
- Joined: Tue Dec 09, 2014 9:58 pm
- My Bike: VS800 Honda Phantom 200
Re: throw-over saddlebag install
Bad idea to put anything over the top of the wires, squashing, chaffing could cause shorts and possibly a fire.
I personally would cut the wires and use these http://www.ebay.co.uk/itm/MINI-2-8mm-EL ... 1688272058
[emoji41]
I personally would cut the wires and use these http://www.ebay.co.uk/itm/MINI-2-8mm-EL ... 1688272058
[emoji41]
Grow old disgracefully young man.
-
- Joined a 1100cc Club
- Posts: 5500
- Joined: Thu Dec 29, 2016 12:33 pm
- My Bike: VS800
Re: throw-over saddlebag install
You can always cut a square out of the yoke to straddle the offending bike parts.
-
- Practicing Bicycling
- Posts: 37
- Joined: Sun Sep 03, 2017 5:40 am
- My Bike: 1996 Suzuki Intruder 1400
Re: throw-over saddlebag install
Thanks. There are already connectors on the wiring harnesses, so I also tried mounting the bags under the electrical stuff. better, but I still can't get the short 8mm bolt in. May have to remove the rubber "feet" on the underside of the seat.Lechy wrote:Bad idea to put anything over the top of the wires, squashing, chaffing could cause shorts and possibly a fire.
I personally would cut the wires and use these http://www.ebay.co.uk/itm/MINI-2-8mm-EL ... 1688272058
[emoji41]
On another note, I think my bag supports may be too small? How should they fit? Do they need to be nearly the size of the bags, or is having half the bag hanging below the brace OK? Not touching anything.
-
- Joined a 1000cc Club
- Posts: 3968
- Joined: Tue Dec 09, 2014 9:58 pm
- My Bike: VS800 Honda Phantom 200
Re: throw-over saddlebag install
Just use a longer bolt. All the supports really do is to keep the back of the bags from being rubbed against the shocks.
[emoji41]
[emoji41]
Grow old disgracefully young man.
-
- Practicing Bicycling
- Posts: 37
- Joined: Sun Sep 03, 2017 5:40 am
- My Bike: 1996 Suzuki Intruder 1400
Re: throw-over saddlebag install
Lechy wrote:Just use a longer bolt. All the supports really do is to keep the back of the bags from being rubbed against the shocks.
[emoji41]
The '96 1400 has springs over the shocks. Do I need to keep the bags from rubbing on those springs? My installed bags rest on the springs and the braces, as the braces are only behind the shocks. Did I order bags that are too big? Thanks. (as should be obvious by now, never had saddlebags before).
-
- Joined a 1000cc Club
- Posts: 3968
- Joined: Tue Dec 09, 2014 9:58 pm
- My Bike: VS800 Honda Phantom 200
Re: throw-over saddlebag install
Over time the movement against the springs will wear a hole in the back of the bags. Think outside of the box and do a little modification to the supports.
[emoji41]
[emoji41]
Grow old disgracefully young man.